Jung Process Systems GmbH
Auweg 2 · 25495 Kummerfeld
Tel. +49 4101 7958-140 · Fax +49 4101 7958-142
info@jung-process-systems.de · www.jung-process-systems.de

Twin-screw pumps

Twin-screw pumps

CHEMSPIN ES – the 3-in-1 solution: Infeed, conveying, and cleaning


The CHEMSPIN ES is a special version of the stainless steel CHEMSPIN pump series. The innovative twin-screw pump with hopper opening is able to handle products with viscosities up to 5000 mPa·s without problems. Its screws are extended at the inlet, so that non-flowable products are drawn in below the inlet opening (like an extruder) and fed to the pump chamber. As a result, external feeding devices are not necessary in many cases. Moreover, product feed is much gentler in this way.

Consequently, the CHEMSPIN ES represents a very attractive 3-in-1 solution: Infeed, conveying, and cleaning are carried out in a single unit. It is available in the sizes 70, 90 and 125.

You have questions?
We will be happy to advise you.

+49 4101 80409-0

QUICK REQUEST
Herausforderung: Entgasen von Säften mit Fasern und Pulpen in der Getränkeindustrie

Consulting:
Henning Grönwoldt-Hesse

Compact Jung twin-screw pump for non-flowable products

CHEMSPIN ES – the 3-in-1 solution: Infeed, conveying, and cleaning

Compact Jung twin-screw pump for non-flowable products
Advantages at a glance
  • Self-feeding properties
    The lengthened feed screws are able to draw in viscous products like a screw conveyor. As a result, external feeding devices are not necessary in many cases.
     
  • Very high flexibility
    Many different products and a wide range of flow quantities and viscosities can be handled by a single pump. Reverse operation is possible – the range of different pumps in a plant can be reduced considerably.
     
  • Safe operation
    Loaded, abrasive or lumpy media can be conveyed – a suitable shaft seal can provide dry-run protection. Very low vibration and noise levels.
     
  • Self-priming, able to handle entrained gas
    Outstanding suitability for emptying & transfer pumping operations.
     
  • High chemical resistance
    The CHEMSPIN is made of 1.4404 stainless steel as standard. Hardened pumping elements and contactless operation ensure high wear resistance.
Technical data / performance features

Type

CHEMSPIN 70ES

CHEMSPIN 90ES

CHEMSPIN 125ES

Max. capacity

10 m³/h

25 m³/h

70 m³/h

Max. delivery pressure

20 bar

25 bar

25 bar

Max. ø of solids

20 mm

30 mm

45 mm

Suction capacity

NPSHr >0.5 m, suction heights up to 9 m possible

Viscosity

0.5 to 1 000 000 mPa·s, higher values after consultation

Pumping temperature

-10 to 180 °C, higher values on request

Cleaning

full CIP cleaning in the plant

Sterilisation

SIP in the plant with steam or hot water

Product-wetted parts

Choice of 1.4404, 1.4539, or 1.4462 – other materials on request

Elastomers

HNBR, FPM, EPDM, FFPM, FDA approval, other elastomers on request

Shaft seals

Single and double-acting floating ring seals, with knife edge for sticky media to prevent start-up damage, single-acting, dry-run safe lip seal

Pump orientation

horizontal, vertical, or sideways (INLINE versions possible)

Connections

Different sizes and connecting standards after agreement

Models

Compact, robust modular design or with free shaft end

Drives

Three-phase, gear, or servo-motors (hygienic stainless steel drives as an option)
Gallery
CHEMSPIN 125ES for pumping resins.
CHEMSPIN 90ES for use in a production plant for adhesives. Here, the lengthened feed screws serve as protection against cavitation.
CHEMSPIN 125ES with large inlet and maximum chamber volume for conveying high-viscosity silicone.
Downloads

CHEMSPIN brochure

©JUNG PROCESS SYSTEMS GmbH 2024    Data Protection   Disclaimer